Fujitsu Printer Issues: Other Common Problems and Fixes

Apart from the common issues you can face in your Fujitsu printer, there are some other not-so-common but significant problems. These problems also need to be eliminated from the printer as soon as possible. So, here you will get to learn about some of the other major issues your printer can have and what is the best solution to those problems.

Issue: The last page does not eject from your Fujitsu printer

Cause: The print job is missing from the ‘form feed’ command.

Solutions:

Method A

• First, you must open a web browser on your computer system and log in to NIC. (Remember, the web browser is the IP of the NIC.)
• After that, click on the ‘configuration’ option and log in.
• When you have to enter the username, type ‘root’ precisely as written in the quotes.
• Next, you need to leave the password section blank.
• Now, go to the ‘print model’ option and click on it.
• Afterward, you need to verify the model. (Note- for port g100, ‘m1’ is the default mode.)
• And then, from the drop-down list, choose the ‘form feed’ trailer.
• Furthermore, go to the bottom of the page and then click on the ‘submit button.’
• In the next step, select the ‘system’ menu option, which is located at the top of the page.
• Finally, press the reboot button and click on the ‘Yes’ option to show that you are sure.

Method B

• First of all, you need to open the telnet session with the help of NIC (Network Interface Card).
• Next, you have to open the DOS window /or use the IP address of the NIC to run the telnet.
• After that, type ‘root’ for the login name and leave the password section empty.
• And then, click on the Enter key.
• Afterward, you have to enter ‘list model m1’ to check the current trailer for model m1.
• Moreover, to set a trailer of ‘form feed’ for model m1, you need to type ‘set model m1 trailer OXOC.’ (The numerical value of the form feeder character is called OXOC.
• In the next step, you type ‘set model m1 trailer $FF’ as ‘form feed’ is defined as variable $FF too.
• To clear the trailer of m1, you need to type ‘set model m1 trailer.’
• When all the changes are done, enter ‘save.’
• After that, you need to type ‘reset.’
• In the last step, the NIC gets reset, and the printer will power cycle itself.

Issue: Getting TCP port busy error messages

Cause: Your Fujitsu printer requires to have the ‘PNE’ port option set to the ‘ethernet.’

Solution

• First, you need to open the front panel of your printer.
• Next, you must keep pressing the menu option until the ‘print management’ appears on the screen.
• After that, move down to the bottom until you see the ‘PNE Port’ option.
• Afterward, press the right arrow button until you come to see the ‘Ethernet’ option.
• And then, you need to click on ‘Enter.’
• In the last step, the PNE port on the printer will be available.

Issue: The printer is telling you to switch the emulation of the printer.

Cause: The emulation of the printer is facing some issues.

Solution:

Method A

• In the first step, you need to get into the NIC using any of the web browsers on your computer device. (Note- The IP of the web address is the IP of the NIC.
• Next, you need to click on the ‘configuration’ option and then log in.
• If you are asked to enter the username, type ‘root’ without the quotes.
• The password section needs to be left empty.
• And then, you are required to click on the ‘print model’ option.
• After that, you need to verify the model. (Note- The default model for port g100 is m1)
• Now, go to the drop-down list and then choose the configuration number. (The acceptable values are 1-8, factory, (None).
• Next, you need to choose the ‘submit’ button at the bottom of the page.
• After that, go to the top of the page and click on the ‘system’ menu function.
• In the last step, press the reboot button and click on the ‘yes’ option to ensure that you agree.

Method B

• First and foremost, you need to open the telnet session with the NIC.
• Next, run the telnet with the help of the NIC’s IP address.
• After that, in the username section, you have to type ‘root’ without quotes and leave the password field empty.
• Then press the enter key.
• Furthermore, you are required to type list model m1’ to check the current configuration for the Model m1.
• If you want to set the model m1 to config #1, enter ‘set model m1 config 1.’ (Also, you need to make sure you do not have space while typing m1 but do give a space between config and 1.)
• Additionally, similar to config #1, you need to type ‘set model m1 config 4’ if you want to set model m1 to config #4.
• (You should not load a configuration that is not saved yet.)
• For setting the model m1 to factory config, you need to enter the ‘set model m1 config 0.’
• To clear the config for m1, enter ‘set model m1 config.’
• When all the process of making changes is done, you need to type ‘save’ to apply the changes and then type ‘reset.’
• At last, the NIC will be reset, and the printer will be power cycled again.